bbcodeclosecopydeletedowndownloadeditellipsiserrorhtmlleftlinkloginlogoutmenuminusmixoriginalplusprivateproresetrightsavesearchsettingssuccessthumbsdownthumbsuptickedunlisteduntickedupuploaduserwaitingwandwarning

oliveira37's test - castle long v2 (clone)

#clone #kentucky #acetyl #toastedalmond #vanillin #bourbon #brownsugar #coconut #oakwood

Castle Long Clone V2
by EWS, Oct 27. 2014, 02:38
http://e-liquid-recipes.com/recipe/58929/Castle%20Long%20Clone%20V2

Acetyl Pyrazine 5% (TPA) 2.00
Bourbon (Vanilla Bourbon) (FA) 2.00
Brown Sugar (TPA) 2.50
Coconut Extra (TPA) 3.00
Kentucky Bourbon (TPA) 6.00
Oak Wood (FA) 2.50 - sub with tpa red oak 2.5
Toasted Almond (TPA) 3.00
Vanillin 10% (TPA) 2.00

1st batch, 03.06.2018
2mg, 30ml

notes:
after 2 months it's still not a finished product. not only kentucky and red oak need a long steep and air to breathe, red oak which was suppose to give an oak barrel accent (and mouth feel) to all the flavours, in fact is muting all the flavours; i don't like this as it is. all i get is a a cheap kentucky bourbon infused with the red oak. i can't taste anything else.

in regards of steeping:
-this recipe needs a long time to steep; 45-60 days; it remained relatively the same for the first 30days, and bloomed a little later compared to v1 (due to red oak, i'm sure), around day 40;

-it needs to breathe! might also need a good amount of space/air between eliquid and bottle neck, so that air can oxidize molecules. not only i'm convinced that this is necessary when using red oak and kentucky bourbon in general, this recipe was made in a small batch bottle filled till the bottle neck (although bottle remained uncapped for the majority of steeping);

-kentucky bourbon is muting everything else; i can get a bit of coconut only in low voltage and for the first two puffs, then it dies; kentucky bourbon is crazy high at 6%; v1 was at 2% and with similar end results;

-vanilla is also not present; i can recognize the weight of the bourbon vanilla, but was expecting more since we use two different vanillas (total 3%). also, vanilla bourbon might be pushing this to the bitter side. and since no sweetener was used...

-both v1 and v2 suck; v2 has as an undesirable red oak accent.

-first time using vanillin, and coconut extra; haven't tried them in single flavour.
-first time combining red oak and kentucky bourbon. i know what to expect from them in single flavour.

possible improvements:
-this needs some thought. steeping procedure or ingredient list ? or both?
kentucky bourbon was used at 6%, this seems too high; moreover, v1 of this clone was at 2% with similar results; flavour doesn't seem to change, only strength.

-i've been trying to improve a clone concentrate (solubarome), and, although the end result is different (i'm convinced they use brandy not kentucky bourbon) i encountered the same difficulties resulting in an unbalanced profile; http://dot1ml.com/mixer/76hg7o9

-i was trying to give some weight and so i added flavours that are known to provide weight but ruined it; i'm learning that alcoholic flavours are difficult to work with, or this recipes needs more work.

Target e-liquid

PG/VG /
mg/ml
ml

Ingredients

Nicotine base (-mg/ml, -/-) -% -ml

PG/VG ratio

/

Strength

mg/ml
PG -% -ml
VG -% -ml
-% -ml

PG/VG ratio

/
-% -ml

PG/VG ratio

/
-% -ml

PG/VG ratio

/
TPA - Red Oak
-% -ml

PG/VG ratio

/
-% -ml

PG/VG ratio

/
-% -ml

PG/VG ratio

/
-% -ml

PG/VG ratio

/
-% -ml

PG/VG ratio

/
This recipe contains unrecognised flavourings. If there are any flavourings or flavouring providers you think should be added to dot1ml please send an email to support@dot1ml.com.

Share/export

Comments

comments powered by Disqus